AC&DC POWER SYSTEMS

We offer products, solutions and services for the entire energy value chain. We support our customers towards a more sustainable future.

ZGX serıes
Regeneratif AC/DC source and load

  • Compact modular design, 15KVA in 4U
  • Bi-directional design
  • Output: AC, DC, AC+DC
  • Single unit: maximum 15KW, 450V L-N, 30A/ph, DC-1KHz output
  • Single phase, 3-phase, split phase, and multi-channel output
  • Various modes: Regenerative AC/DC source, regenerative AC/DC load, BiPolar DC source
  • Regenerative RLC load in full frequency range
  • True current source in CC mode
  • Up to 100th harmonics waveform generation, inter-harmonic generation
  • Error locating function
  • 24 months warranty

DATASHEET >

ESA Series
bıdırectıonal (Regeneratif) AC power source

  • Output Power: Standard up to 4MVA and can be configured to higher Power
  • 4 quadrant operation, regenerative up to 100% of rated output power back to grid (-R option)
  • Independent three-phase output
  • Up to 50th harmonic waveform generation
  • Regenerative AC load function (-LD option)
  • Line impedance (RL) simulation (-IMP option)
  • ON/ OFF output phase angle can be programmed
  • Current limit can be programmed, output can be shorted for short circuit test

DATASHEET>

KGS Series bıdırectıonal (Regeneratif)
ac power source

  • Modular design, output power from 15kVA to 1080kVA
  • Bi-directional AC/DC power source, seamless transition between source and sink modes
  • Regenerative AC/DC load function
  • Output: AC, DC, AC+DC
  • Using true current feedback control when working in CC mode
  • Frequency Range: DC~ 5kHz
  • Soft start: effectively restrain the impulse current when power on
  • Up to 100th harmonic waveform generation, inter-harmonic generation
  • Max output 450V L-N within output frequency range from DC to 5kHz
  • RLC Load Simulation & RCD Load Simulation
  • Analog signal input for use as a power amplifier (delay ≤ 20 µs)
  • 30 Built-in harmonic waveforms

DATASHEET>

ESD Series bıdırectıonal (Regeneratif) DC power supply

  • Single system up to 500kW, up to 4MW and above
  • Output voltage up to 2000V(std), higher voltage can be customized
  • Applications: battery simulation, battery test (-BSS option), PV simulation (-PV option)
  • Program accuracy up to 0.1%
  • Seamless transition between source and sink modes (-R option)
  • Current rise time (10% -90%) <1ms (-BSS option)
  • CC/CV/CP/CR mode available
  • Regenerative DC load function (-LD option)
  • Hardware & software for PV Simulation (-PV option)
  • Low-Voltage operation mode (-ZV option)Output terminal insulation monitoring function (-INS option)

Datasheet >

BSL Series
hıgh power
DC power supply/load

  • Output Power: 100kW/150kW/200kW/250kW/300kW
  • Output Voltage: 1000V/1500V/2000V
  • Output Current: *2 / *3 / *4
  • Auto-Ranging Output
  • Soft start: effectively restrain the impulse current when power on
  • Seamless transition between source and sink modes
  • Current rise time (0% -90%) <5ms
  • CC/CV/CP/CR mode available
  • Regenerative DC load function

Datasheet>

RegeneratIve AC electronIc Load

ESA/KGS series  can be used as regenerative AC electronic load. This function consists of CR mode, Rectifier mode, CC/CP phase lead/lag mode. CR mode is used to simulate three-phase resistive loads, the CR mode and three-phase resistance parameters can be set through the panel and can realize the program of resistance sequence. Rectifier mode can be used to simulate non-linear loads, the CC/CP mode and CF (setting range: 1.414~3) parameters can be set through the panel. CC/ CP phase lead/lag mode can simulate sinusoidal current, Constant current CC and constant power CP modes are available to adjust load current or power, phase angle can be set from 90° to -90° simulating the voltage and current conditions under inductive and capacitive loads

ESA Datasheet

Regeneratif DC elektronik Yük

ESD series with -LD option can be used as regenerative DC electronic load. DC load simulation includes constant current, constant resistance, constant voltage, and constant power modes.

ESD series DC electronic load with -ZV option can produce large current that meets the requirements under the input condition close to 0.4V, which can evaluate the electrical characteristics of the fuel cell (such as VI), etc.

ESD Datasheet